How To Clean Beard Trimmer – 5 Simple Steps

Table of Contents

You might believe that using the bear trimmer repeatedly without cleaning it is safe and harmless. Of course, unlike razors, a beard trimmer is much safer as it does not graze over the open skin. However, without adequate cleaning and maintenance, the performance of your beard trimmer could slowly dwindle.

If you take proper care of your trimmer, it is likely to last a lifetime. So, it’s important to clean it regularly and keep it working properly for years to come.

Along with that, a lack of hygiene and cleaning can also turn your beard trimmer into a hotspot for bacteria. You see, after a few trims, your beard trimmers are going to get clogged with dead skin, debris, dust, and clippings. Over time, they can make their way into the crevices and corners of the trimmer, allowing bacteria to thrive.

When it comes to cleaning trimmers, there is more to it than just washing with hot water. If you want to learn HOW TO CLEAN A BEARD TRIMMER, you have come to the right place.

In this article, we put together 5 simple steps that will help you achieve this. So, without any further ado, let us get started!

CHECK FOR WET/DRY CAPABILITY

Before rinsing your beard trimmer with water, check whether your beard trimmer has a wet/dry capability. This is because not all electric devices can be rinsed. This is especially true for corded beard trimmers. So, if your beard trimmer plugs into the wall, do not try rinsing it. However, many cordless beard trimmers are also not designed to repel water.

So, if you plan to buy a new beard trimmer, make sure that you are going for a model with wet/dry capability. This will make cleaning much easier and allow you to run hot water over the trimmer resulting in a quick clean.

The Panasonic Wet and Dry Cordless Electric Beard and Hair Trimmer [https://www.amazon.com/Panasonic-Cordless-Electric-Beard-Trimmer/dp/B01M24BKOZ] could be a decent option. This beard trimmer features sharp blades at a precise 45 degrees angle, resulting in an easy and superior trim. Along with that, the quick-adjust dial on this beard trimmer allows you to add 0.5mm increments starting from 1mm up to 10mm.

FLICK OUT TINY HAIRS AND DEBRIS

Many of us ignore the tiny brush that comes with beard trimmers. Yet, that little brush has a big significance. You can use it to flick out the tiny hairs and debris that may be clogging the crevices of your beard trimmer.

This should be done before running water through the trimmer, as dry hairs and debris are easy to remove. However, if you seem to have lost the tiny brush, worry not because we have an alternative for you.

In this case, find a toothbrush with soft strands. Make sure that you are not using an old toothbrush with hardened bristles. Otherwise, it may damage the blade of your trimmer. Rather, what you want is a toothbrush that has firm bristles. Alternatively, you can also use a toothpick to pick out any debris from crevices where the toothbrush cannot reach. However, this must be done with great care, as toothpicks are hard and can damage the beard trimmer’s small components.

After flicking out the dry debris, put on a small amount of soap on the toothbrush and gently rub it over and through the trimmer’s teeth. Then, run warm water over the teeth. This is an essential step, as it will help disinfect your beard trimmer and get it rid of bacteria.

After rinsing the beard trimmer, repeat the process a few times until your trimmer’s teeth have cooled down adequately.

DRY UP THE BEARD TRIMMER

After rinsing, do not try to use the beard trimmer right away. Furthermore, do not plug it into charging either. Since some components of your beard trimmer might still be wet, you would not want to zap it by turning it on.

Furthermore, avoid storing the trimmer away without drying it up first. Otherwise, your trimmer may end up accumulating bacteria again. Furthermore, it may also rust. Both defeat the entire purpose of cleaning the trimmer in the first place.

So, let your trimmer try in the open air. Alternatively, you can also use a blow dryer at a normal setting to dry the trimmer quickly and efficiently. During the drying process, make sure that the trimmer does not accumulate any dirt.

LUBRICATE IT

Apart from the tiny brush, another important component that beard trimmers usually come with is the trimmer oil. Of course, just like the brush, many of us also tend to ignore the oil. However, it also carries equal significance.

You see, the teeth and blades of the trimmer are mechanical parts that rub against each other when they work. And for proper movement of the small mechanical parts, lubrication is necessary. This is where this small bottle of oil will help you.

Without proper lubrication, your trimmer is going to wear down much quicker. Eventually, this will have a significant impact on its performance. Since of it as the same thing as adding grease into the chain of a bicycle.

But if you have lost the oil just like many other people, worry not, because you have some alternatives. For instance, you could buy the Wahl Premium Hair Clipper Blade Lubricating Oil [https://www.amazon.com/Wahl-Hair-Clipper-Blade-3310-300/dp/B0084AWBRS/ref=sr_1_1?dchild=1&keywords=beard+trimmer+oil&qid=1616331841&sr=8-1] . This beard trimmer oil is specifically designed to keep the small parts of your trimmer working smoothly and efficiently.

It features rust prevention capabilities that extend the life of your clipper blades. The process of lubricating your beard trimmer is quite simple and as follows:

  1. Open the tip of the lubricating oil
  2. Squeeze out two-three drops of the oil on to the blades
  3. Spread it evenly on the blades with the help of a wipe or fingers
  4. Use tissue paper to wipe off the excess oil
  5. Turn the trimmer on for a few seconds to distribute the oil evenly between the blades

It is that simple and straightforward. Again, it is recommended to let the trimmer sit in the open for a while after lubrication. You would want the excess oil to evaporate before placing it away. But since oils are sticky, they can also easily accumulate dust. So, avoid letting the trimmer dry up in a dusty environment.

STORE IT AWAY

After a thorough cleaning, it is time to store your trimmer away until the next use. Avoid keeping it out in the open to prevent the accumulation of dust. Rather, store it indoors in a cupboard, preferably packed inside the case/pouch that it originally came in. We do not recommend storing the trimmer out in the open for better hygiene.

If you do not have the original pouch or case, the simplest method would be to wrap the trimmer in a clean piece of cloth and place it in your cupboard.

Alternatively, you can also buy the Aproca Hard Travel Storage Case for Wahl Hair Clippers [https://www.amazon.com/Aproca-Storage-Clipper-Stainless-Clippers/dp/B07M7C9QY2/ref=sr_1_16?dchild=1&keywords=beard+trimmer+pouch&qid=1616332346&sr=8-16] . This storage case provides absolute protection to your beard trimmer. It is made of a 1680D high-density material that is quite durable and absorbs shocks well. In specific, it is designed for the 9818 Wahl Clippers and shavers. Furthermore, the Braun MGK3060 also fits inside it.

CONCLUSION

After reading this simple guide, we hope that you now thoroughly understand HOW TO CLEAN A BEARD TRIMMER. These steps are not very difficult to follow. They are simple and can be completed with the help of only a few basic tools.

So, what are you waiting for? Get your trimmer out and clean it to maintain top performance and hygiene. Additionally, you may also check the manual that came with your beard trimmer. In the manual, you may find specific cleaning details regarding your specific beard trimmer model.

FREQUENTLY ASKED QUESTIONS WHAT ARE WET/DRY BEARD TRIMMERS?

Wet/Dry beard trimmers are those that can be used in both wet and dry conditions. These trimmers repel water and prevent it from passing through the outer structure of the trimmer. Hence, you can easily rinse such trimmers underwater without the risk of zapping

them.

WHY IS IT IMPORTANT TO CLEAN BEARD TRIMMER?

Proper cleaning and maintenance of beard trimmers are necessary for better hygiene and performance. Otherwise, your beard trimmer will become a hotspot for bacteria and may also begin wearing out. This will significantly reduce its power resulting in an eventual device failure.

HOW OFTEN SHOULD I CLEAN MY BEARD TRIMMER?

We suggest cleaning the beard trimmer once after every 3 weeks or after 2-3 uses.

HOW OFTEN SHOULD I LUBRICATE THE CLIPPER BLADES?

The clipper blades should be lubricated at least once after every 3 uses. This is essential for the smooth working of the mechanical parts that rub against each other. Without lubrication, these parts will end up running down.

WHAT SHOULD THE WATER TEMPERATURE BE?

We do not suggest running hot water over your beard trimmer. At most, you should be using lukewarm water for rinsing purposes. Hot water can damage the components of your beard trimmer and can also increase the likelihood of rusting.